Coal merchants, QuettaDelivering to Punjab and Karachi

اردو
0349 4384514Get a quote

Articles / 3 min read

Clinker in a coal boiler or furnace: why ash fuses and how to stop it

Clinker is coal ash that has melted and set into hard glassy lumps on or above the grate. Plants that went back to coal this year often meet it in the first few weeks: the lumps cover the air holes, the fire runs uneven and the boiler loses output.

Flames inside the firing mouth of a small kiln
Fig. 1Flames inside the firing mouth of a small kiln. Stock photo

Why ash fuses

Ash is a mix of minerals that melts over a range of temperatures. When the fuel bed runs hotter than the ash can stand, it turns sticky and sets into clinker as it cools. Blocked air makes some places hotter, which makes more clinker, and the operator who opens the dampers makes it worse.

Four things combine: ash that melts easily, a lot of ash, uneven air and a bed that runs too hot. Iron, calcium, sodium and sulphur compounds lower the melting point, and the sheet cannot tell you that. A lab can, with the ash fusion test, which reports the temperatures at which a cone of the ash deforms, softens, becomes hemispherical and flows. Ask for it and for an ash analysis with every grate-boiler lot, not only heat and sulphur. Fines pack the bed and restrict air, and swings in moisture change the bed temperature hour to hour.

Symptom, likely cause, first check

Work down from the cheapest check. Most clinker yields to a change in operation before it needs a change in coal.

Troubleshooting clinker
What you seeLikely causeFirst check
Hard lumps stuck to grate barsBed too hot or ash melts lowLower bed temperature, open more primary air, ask for the ash fusion test
Fire dark in patches, bright in othersUneven coal size or fines in the feedScreen the coal and reduce the fines share
Clinker only on some daysMoisture or ash changes between lotsCompare lab reports and delivery dates
Clinker grows every shiftGrate not cleaned often enoughShorten the cleaning interval, check grate speed
Clinker after a switch from gasGrate and air set for another fuelSet air, bed depth and coal size in a commissioning run
Steam falls with the same feed; air pressure under the grate risesAir holes blocked by old clinkerClear the holes, look for worn bars
Red valve wheels on steam pipes in a boiler room
Fig. 2Red valve wheels on steam pipes in a boiler room. Stock photo

Fixes on the boiler, then the coal

Keep bed depth steady and not too deep, hold primary air in range because too little lets the bed overheat, clean the grate on schedule, screen out oversize and dust, and keep coal dry. If clinker persists the coal is the next suspect. Sor Range and Chamalang lump leave less ash per tonne, which is no promise against fusion, so try a small trial of cleaner coal and compare clinker over a week. The article on how to read a coal analysis explains each line of a report. A hand-fired furnace gives the most control and least consistency; a chain or travelling grate shows a change of coal quickly as clinker; a fluidised bed holds the bed below the point where most ash melts. When you change coal, run the new fuel at part load first.

A grate and bed routine
How oftenTask
Every shiftClean the grate and remove ash and clinker on schedule; check the fire is even across the grate
Every shiftCheck feed size: screen out dust and oversize pieces
Every deliveryWeigh the truck, take a sample, record the lot with heat, ash and moisture figures
WeeklyLook for blocked air holes and worn bars
MonthlySend a sample to a lab for ash analysis and fusion temperatures
Write the lot, date, load, air setting and what came out of the grate in a log. After a month, clinker will follow one supplier, lot, wet week or operator.

Breaking it out safely

Clinker holds heat long after the fire has died back. Let the boiler cool as the maker advises, use long tools, heat-proof gloves and eye protection, keep clear of the door when you open it, and never put water on hot clinker because the steam burns. The article on coal ash uses and disposal covers where it goes afterwards.

Questions people ask

What is an ash fusion test?

A lab test that reports the temperatures at which an ash cone deforms, softens, becomes hemispherical and flows. Ask for it when buying coal for a grate boiler.

Which coal has the least ash?

On our sheet Sor Range has the lowest typical ash, then Chamalang lump. Check the lab report for your lot.

Prices are indicative, per tonne, excluding sales tax, and change week to week. See today's sheet or ask us for a confirmed price.

GradesIn this guide

Grades mentioned

A heap of coal pieces, close-up

The cleaner local coal, for boilers

Sor Range coal

Origin
Sor Range and Degari, Quetta
Heat value
6,000–7,000 kcal
Size
Lump or mixed
For
Textile and industrial boilers, brick kilns

FromRs 39,250per tonne, ex-yard

Dark, shiny pieces of coal, close-up

Higher-grade lump for kilns and cement blending

Chamalang coal

Origin
Chamalang, Loralai–Kohlu, Balochistan
Heat value
5,800–6,800 kcal
Size
Lump
For
Brick kilns, cement (blended)

FromRs 40,000per tonne, ex-yard

Lumps of black coal, close-up

Balochistan's most traded coal, lump or run-of-mine

Duki coal

Origin
Duki, Loralai, Balochistan
Heat value
5,500–6,500 kcal
Size
Lump or mixed
For
Brick kilns, small industry

FromRs 34,000per tonne, ex-yard

QuotationToday's price

Get a confirmed price.

Tell us what you need. We send you a written price within 2 working hours.

You sendCoal, tonnes, city
We replyWritten price in 2 h
We deliverKarachi and Punjab in 2–3 days
A loaded haul truck on a mine road
Coal
Tonnes

Written price within 2 working hours.

Private. Your number is only used to send your price.

Prefer WhatsApp? 0349 4384514

Delivery and guidesAll cities

Keep reading, or get coal delivered.