Articles / 4 min read
Coal for lime kilns (chuna bhatti): grade, size and ratio
Coal for lime kilns has to hold 900 to 1,100°C through the whole charge, and in a mixed feed kiln its ash and sulphur stay in the lime you sell. That makes a chuna bhatti pickier about coal than a brick kiln.

What burning lime asks of the fuel
Limestone is calcium carbonate. Heat drives off carbon dioxide and leaves quicklime, so 100 kg of pure stone gives 56 kg of lime and 44 kg of gas, and a tonne of lime needs about 1.8 tonnes of stone.
Kiln patents describe a burning zone of about 900 to 1,100°C, with 950 to 1,050°C giving a reactive lime. Too cool and the stone stays raw in the middle. Too hot for too long and it goes dead burnt and slakes badly. Practical Action puts the theoretical heat for pure calcite at about 3,200 MJ a tonne of lime, which is about 764,000 kcal, or about 118 kg of Sor Range at 6,500 kcal/kg if no heat were lost. No kiln reaches that, because heat also leaves in the hot lime and the exhaust.
Coal per tonne of lime: four references
Practical Action's guide to a small vertical shaft kiln at Chegutu in Zimbabwe says it makes good lime at about 7.5 parts limestone to 1 part coal by weight and turns out 1 to 1.5 tonnes of quicklime a day. Seven and a half tonnes of pure stone give 4.2 tonnes of lime, so that works out to about 238 kg of coal per tonne of lime. It is a different design and different coal, so it does not set the figure for yours.
For older batch kilns, which are closer to many traditional bhattis, historical figures put coal at half a tonne or more per tonne of lime. A modern shaft kiln needs about 4.5 to 5 MJ per kilo of lime. On Sor Range that is roughly 165 to 185 kg of coal, which at the indicative delivered price of Rs 52,250 a tonne is about Rs 9,410 per tonne of lime at 180 kg. Most chuna bhattis sit somewhere between the modern shaft kiln and the old batch.
- Theoretical, no heat lost118 kg of coal
- Modern shaft kiln (midpoint)175 kg of coal
- Zimbabwe shaft kiln238 kg of coal
- Old batch kiln500 kg of coal
Modern shaft: 4.5 to 5 MJ per kg of lime is 1,075 to 1,195 kcal, divided by 6,500 kcal/kg, so 165 to 184 kg; the bar shows 175. Old batch kiln is the low end of 'half a tonne or more'.

What ash and sulphur do to the lime
In a mixed feed kiln, stone and coal go in together from the top and the coal ash stays with the lime. More ash means more grit and less pure lime in the bag, which hurts most on whitewash and with buyers who test purity.
Sulphur dioxide from the coal reacts with the hot lime and stays as calcium sulphate. Builders usually tolerate that. Steel making often wants lime below 0.1% sulphur and sometimes 0.03%, which local coal will struggle to give in a mixed feed kiln.
Which grade suits a chuna bhatti
Sor Range is the cleanest Balochistan coal we sell, around 6,500 kcal/kg, 9% ash and 3% sulphur. Chamalang lump is close behind at 6,300 kcal/kg and 11% ash. Duki lump works for building lime but brings 15% ash and about 4.5% sulphur. Mach / Harnai and fines carry 20 to 25% ash and 5 to 6% sulphur, and belong in a lime kiln only when the lime is for rough use.
| Grade | kcal/kg | Ash % | Sulphur % | Coal per tonne of lime | Cost (Rs) |
|---|---|---|---|---|---|
| Sor Range | 6,500 | 9 | 3 | 175 kg | 9,120 |
| Chamalang lump | 6,300 | 11 | 4.5 | 180 kg | 9,550 |
| Duki lump | 6,000 | 15 | 4.5 | 189 kg | 9,790 |
| Mach / Harnai | 5,800 | 20 | 6 | 196 kg | 8,900 |
| Coal fines | 5,000 | 25 | 5 | 227 kg | 8,620 |
Coal size and stone size
A shaft kiln lives on air rising through the charge. Fines and dust fill the gaps between stones and choke the draught, which leaves raw cores. Practical Action warns that soft stone that crumbles, and fine material generally, block the airflow in a vertical kiln. Use lump coal screened free of dust, as the article on coal sizes explains.
Stone should be broken to a fairly even size. Big pieces stay raw in the core, small pieces and powder pack the gaps. Soft or chalky stone crumbles on the way down and makes its own fines inside the kiln, so with that stone a lower stack and gentler loading help more than a change of coal. A grey, heavy lump that will not slake is raw or dead burnt, and the cure differs, so look at where in the kiln it came from.
Records for each burn
Coal divided by lime from each burn gives your own ratio, which is worth more than any book. Try one truck of a cleaner grade and compare coal per tonne and lime quality. Our fuel cost calculator turns coal per tonne of lime into rupees.
- Weight of stone loaded and its size range.
- Weight, grade and size of the coal.
- Hours the fire was running.
- Weight of lime drawn, and how much was raw or overburnt.
- Colour of the lime and how fast it slakes.
Prices are indicative, per tonne, excluding sales tax, and change week to week. See today's sheet or ask us for a confirmed price.



