Articles / 3 min read
Sulphur in coal: what it does to a boiler or kiln and how to manage it
Sulphur in coal from Balochistan runs 3% to 6%, and a buyer who has used imported coal sees it in the chimney, the boiler tubes and the bricks. It can be managed once you know where it goes when the coal burns.

Where the sulphur comes from
Swamps reached by seawater pick up sulphate, and bacteria turn it into pyrite and sulphur bound into the coal itself. Pakistan's main coals formed in the Paleocene and Eocene, many in coastal swamps, and a USGS study found shallow-water fossils with the Sor Range beds. Pyrite shows as brassy heavy grains in a lump and some of it can be washed out; organic sulphur cannot.
Imported South African steam coal is commonly around 1%. Thar lignite is also near 1% on PACRA's figure, at 2,770 kcal/kg net, which is a different fuel.
- Sor Range60 kg of SO2
- Duki lump90 kg of SO2
- Chamalang lump90 kg of SO2
- Duki run-of-mine100 kg of SO2
- Coal fines100 kg of SO2
- Mach / Harnai120 kg of SO2
SO2 = sulphur % x 20 kg per tonne, because 1% of a tonne is 10 kg of sulphur and each kg of sulphur makes 2 kg of SO2. Sulphur from our sheet, as received.
In the boiler and the kiln
A little of the SO2 turns to sulphur trioxide, which forms sulphuric acid when the flue gas cools below its acid dew point. The acid eats economisers, air heaters, ducts and the base of steel chimneys, and it is worst in a boiler that runs part load or stops and starts. Pyrite also makes stockpiles heat up faster.
In brick kilns, fuel sulphur shows as white scum and discolouration on the faces. Lime made with high-sulphur coal picks up calcium sulphate. Cement kilns absorb much of it into the clinker, but too much out of balance with the alkalis causes build-up and rings in the preheater, which is why cement plants write a sulphur limit into coal contracts.
In the air, SO2 irritates the throat and forms sulphate particles that add to the winter haze over Punjab. A kiln burning 10 tonnes a day of Duki lump at 4.5% sends out about 900 kg of SO2; the same tonnage of Sor Range at 3% sends out about 600.

Ways to manage it
Blend. Sor Range at 3% mixed with Duki at 4.5% or Mach at 6% brings the average down, and the mix must be made before the grate, not fed in turns. Keep the flue gas leaving the economiser and air heater well above the acid dew point and check your boiler maker's minimum exit temperature. Insulate steel chimneys and avoid long periods at very low load. Buy on analysis, with total sulphur on every lot and the basis stated.
| Sor Range : Mach / Harnai | Sulphur % | Heat (kcal/kg) | Ex-Quetta, Rs a tonne |
|---|---|---|---|
| 100 : 0 | 3 | 6,500 | 39,250 |
| 75 : 25 | 3.8 | 6,325 | 37,563 |
| 50 : 50 | 4.5 | 6,150 | 35,875 |
| 25 : 75 | 5.3 | 5,975 | 34,188 |
| 0 : 100 | 6 | 5,800 | 32,500 |
Limestone in a fluidised bed
In an FBC or CFBC boiler crushed limestone in the bed captures SO2 as calcium sulphate, best near 850 degrees C and falling off above about 900. A tonne of coal at 4.5% holds 45 kg of sulphur. Pure limestone is 100 units to 32 of sulphur, so capturing all of it takes about 141 kg, and a calcium to sulphur ratio of 2 doubles that to about 281 kg a tonne of coal. Real limestone is less pure, so treat that as a planning floor and ask the boiler maker for the ratio they guarantee. More limestone means more solid waste, which is why a lower-sulphur coal sometimes saves more than it costs.
Sor Range is Rs 39,250 a tonne ex-Quetta against Rs 32,500 for Mach / Harnai, confirmed when you contact us. For a boiler with a costly air heater or a cement plant with a sulphur limit the difference often pays for itself; a kiln that just needs heat may do with a blend.
Questions people ask
Which coal has the lowest sulphur in Balochistan?
Sor Range and Degari coal near Quetta, about 3% in our lots, against 4.5% to 6% for Duki, Chamalang, Mach and Harnai.
Prices are indicative, per tonne, excluding sales tax, and change week to week. See today's sheet or ask us for a confirmed price.



