Tools / Prices as of 16 November 2026
Coal stockpile weight calculator
Got a heap of coal in the yard and want to know how much is left? Measure it with a tape and this works out the tonnes, the maunds and how many truckloads it holds.
1 What shape is the pile?
2 Measure it
Length along the bottom, width across the bottom, and height at the top.
3 Which coal is it?
Fine-tune the figures
Bulk density, t per cubic metre
Leave empty for 0.85. Lump with gaps is lighter (about 0.8), wet fines heavier (about 0.9 or more).
Long pile of Duki run-of-mine
46.2 tonnes
About 1,155 maunds of 40 kg.
- Volume
- 54.4 m³ (1,920 cubic feet)
- Truckloads
- 1.03 on 22-wheelers
- Worth at our ex-Quetta price
- Rs 1,571,245
A tape measure gets you within about 10 to 15%. For buying and selling, go by the weighbridge.
Order more coalHow the calculation works
The pile's volume comes from its shape. A long peaked pile is treated as a triangle across times its length, a round heap as a cone, and a walled bay as a box. Measure along the bottom and up to the top.
Volume times bulk density gives the weight. Loose coal weighs roughly 0.8 to 0.9 tonnes a cubic metre depending on size and moisture, so 0.85 is used unless you put in your own. A maund here is 40 kg.
Results are estimates for planning. Coal prices are indicative and confirmed when you contact us.
A worked example
A long peaked pile 40 feet long, 16 feet wide at the base and 6 feet high.
A tape measure gets you within about 10 to 15%; for buying and selling, use the weighbridge.
Prices in this example are from our sheet in late October 2026; the calculator above always uses the current sheet.
- Volume
- ½ × 16 × 6 × 40 = 1,920 cubic feet, about 54 m³
- At 0.85 tons per m³
- about 46 tons
- In maunds of 40 kg
- about 1,150 maunds
- Truckloads
- about one full 22-wheeler
Questions about this calculator
How many tonnes are in a coal pile?
Measure length, width and height, work out the volume for its shape, and multiply by about 0.85 tonnes per cubic metre. The calculator does it for long piles, round heaps and bays.
How much does one cubic metre of coal weigh?
Loose coal weighs about 0.8 to 0.9 tonnes per cubic metre. Lump with air gaps is at the light end; wet fines are heavier.
How many kg is one maund?
In trade in Pakistan a maund is taken as 40 kg, so a tonne is 25 maunds.
More tools and reading
- Brick kiln coal calculatorCoal per lakh bricks, trucks a month, and which grade gives the lowest cost per brick.
- Boiler coal consumption calculatorCoal per hour, day and month from your steam output, with the monthly bill.
- Switch to coal: fuel cost calculatorPut in what you pay for gas, LPG, diesel or wood and see the same heat from coal.
- Coal truck and freight calculatorTrucks needed, freight per tonne, and own transport against delivered.
- Coal analysis converterAs received, air dried, dry and ash free in one table, with NCV and kcal to MJ.
- Compare two coal offersWhich of two offers gives more heat per rupee, after freight.
- Legal truck load calculatorThe legal coal load for your truck under the axle limits.
- Sales tax on coal calculatorSales tax per tonne and the price with tax for your order.
- How to store coal at your site without fires or wet stockTo store coal safely, keep the pile low, compacted and short-lived, and read its temperature. A big loose heap can warm itself into a smoulder with no flame anywhere near it, and an open one soaks up rain and fog.
- Coal sizes explained: lump, run-of-mine, nuts and chooraCoal sizes decide how a fuel burns: two trucks of the same Duki coal behave differently if one is lump and the other mostly dust. These are the mm ranges we load and what each size is for.
- How to check coal quality when the truck arrivesCheck a coal truck before it tips, because after the load is mixed into your stock a complaint is nearly impossible to prove. The routine takes about ten minutes and goes in this order.